If I do a ‘show running-config’, you can see the hostname is R1. There is no startup-config, therefore, the Setup Wizard will run.įor example, we have router R1. Then, reload the device, and it will boot up with a blank configuration. The phone does not reset.To do a factory reset, we use the ‘write erase’ command at the enable prompt. If you do not complete this key sequence or do not press any keys, after 60 seconds the Headset, Mute, and Speaker buttons no longer flash, and the phone continues with its normal startup process. If you repeat a key within the sequence, for example, if you press 1 223456789*0#, the sequence is still accepted and the phone resets. The line buttons flash in sequence in order to indicate that the phone waits for you to enter the key sequence for the reset. Otherwise, the phone goes through the factory reset process. If you press another key or do not respond to this prompt within 60 seconds, the phone continues with its normal startup process and does not reset. In order to reset the network configuration settings when the phone resets, press 2. In order to maintain the current network configuration settings for the phone when the phone resets, press 1. If you enter this key sequence correctly, the phone displays this prompt: If you enter an invalid key sequence, the buttons no longer flash, and the phone continues with its normal startup process. If you do not complete this key sequence or do not press any keys, after 60 seconds, the Headset, Mute, and Speaker buttons no longer flash, and the phone continues with its normal startup process. If you repeat a key within the sequence, for example, if you press 1223456789*0#, the sequence is still accepted and the phone resets. Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash. The Headset, Mute, and Speaker buttons flash in sequence in order to indicate that the phone waits for you to enter the key sequence for the reset. Immediately press and hold # and while the Headset, Mute, and Speaker buttons begin to flash in sequence, release #. Unplug the power cable from the phone, and then plug in the cable again. #CISCO32979 IP AND PASSWORD FACTORY PASSWORD#In order to perform a factory reset of a phone if the password is set, complete these steps: Reset the 79 IP Phones to the Factory Default All settings are deleted.Ĭhoose Menu > Network Config in order to reconfigure the network settings for your WLAN. The phone displays the Restore to Default? message. Reset the Cisco 7920 Wireless IP Phone to the Factory DefaultĬomplete these steps in order to reset the Cisco 7920 Wireless IP phone to the factory default:Ĭhoose Menu > Phone Settings > Factory Default. Note: Power cycle the phone or press any of these keys while in the first level submenu and then press the green key to hide the options: Press the green key to open the administration mode. Press (the pound key), and then press (the pound key) again. Start the Administration Mode on the PhoneĬomplete these steps in order to open the administration options on the Cisco Unified Wireless IP Phone 7920 so that you can access the hidden options on the Phone menu: You need to start the administration mode on the phone in order to use the options. Reset the 7920 Wireless IP Phone to the Factory DefaultĪdministration options in the Network Config and Phone Settings menus are hidden by default to ensure that users do not make changes that can affect the operation of the phone. Refer to Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment. #CISCO32979 IP AND PASSWORD FACTORY SOFTWARE#Components UsedĬisco IP phones 7920, 7940, 7960, and the software are not restricted to any specific release. Prerequisites RequirementsĬisco recommends this document for personnel involved with IP Telephony networks. #CISCO32979 IP AND PASSWORD FACTORY HOW TO#This document describes how to reset the Cisco 7920, 79 IP phones back to the factory defaults.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |